Video Transcript
Using CXD-Q Amplifiers
3m 4s
0:08
In Q-SYS Designer version 4.0 and beyond,
0:12
there’s a new inventory item that’s worth taking a moment to look at.
0:16
This is the CXD-Q Series of networked amplifiers.
0:20
To add one to your design, simply click on the Plus icon in the Inventory Panel,
0:24
select Amplifiers, and then select one of the three models.
0:28
Even though they’re found under amplifiers,
0:30
they would also be just as comfortable in the Peripherals section .
0:33
You see, these new amplifiers are unique
0:36
because in addition to amplifying the signals to the loudspeakers,
0:40
they also serve as remote input connections to the system.
0:43
CXD-Q amplifiers are based on QSC’s revolutionary CXD Series of amplifiers,
0:49
but these ones have been specially modified to integrate with Q-SYS.
0:53
On the rear panel of each amplifier you’ll find Mic/Line Inputs,
0:57
which means that this device has the functionality of both a DataPort amplifier
1:01
and an I/O Frame with a Mic/Line Input Card.
1:04
You can drag the Input component into your design and treat it just as you would any other IO Card,
1:09
and route audio anywhere you like within your design.
1:13
The Amplifier block works much the same as an IO Output Card,
1:16
except that its output pins would go directly to your loudspeaker components.
1:20
Its control panel offers you all the same monitoring information
1:24
and control of a QSC DataPort amplifier,
1:27
as well as a few extra buttons that lock out controls on the device’s front panel.
1:32
These devices have some additional components in common with the I/O Frame,
1:36
including the ability to turn on phantom power
1:39
for any of your channels, and it also has its own GPIO terminal.
1:43
The three models of CXD-Q amplifiers have different power ratings,
1:47
which you can review in the inventory menu.
1:50
The CXD-Q 4.3 and 4.5, for instance, can provide 70V power,
1:55
while the 4.2 cannot. Regardless of which model you select,
1:58
they operate the same way in the Designer software.
2:02
In their Properties panel you have a new field called Channel Configuration,
2:06
that allows you to combine channels in both parallel
2:08
or bridged modes based on QSC’s Flexible Amplifier Summing Technology, known as FAST.
2:15
For more information on FAST as well as the CXD Series,
2:19
check out the PLD/CXD Training Course on qsctraining.com.
2:24
Whenever you change the channel configuration of your amplifier,
2:27
which you may need to do when you first deploy your design,
2:30
you will need to confirm the CXD-Q Channel configuration change manually on the front panel.
2:35
Changing the channel configuration will also mute all four channels,
2:39
which you can unmute by either tapping the power button
2:41
or by selecting this button in the control panel.
2:44
Then after that, you only need to do that if you change the channel configuration again.
2:49
So if you’re using Q-SYS and you need both an amplifier and a few inputs situated near that amplifier,
2:55
the CXD-Q is the ideal solution. Thanks and we’ll see you next time.
Tips and Definitions
Using CXD-Q Amplifiers
3m 4s
Because it is a networked amplifier, the inputs from the CXD-Q amplifier can be routed anywhere on the Q-LAN network. Transversely, you can feed its outputs from anywhere in your design.
CXD-Q amplifiers will not operate without a Q-SYS design. You cannot use this amplifier in a stand-alone setting.
Lesson Description
Using CXD-Q Amplifiers
3m 4s
Learn how to configure amplifier channels and use its on-board I/O to route on Q-LAN.